File Repairer
Windows 10 & 11 Buy license · $29.95
Videos

How to Repair Drone, Dashcam and Action Camera Videos

Drone, dashcam or action cam clip won't play after a crash or power loss? Protect the card, then rebuild the video with a sample clip from the same device.

Updated 5 minute read The File Repairer team

To repair a drone, dashcam or action camera video that won't play, copy the whole memory card to your PC, find the broken clip and repair it with software that supports sample-file repair. These cameras usually break videos the same way: power is lost before the recording is closed, so the file's index is never written. Adding a working clip from the same device, recorded with the same settings, lets the repair rebuild the missing structure, picture and sound.

Drones, dashcams and action cameras record in tough conditions: on batteries that can run flat mid-flight, in cars that cut power when the engine stops, and while being shaken, dropped or crashed. Here is why their videos get damaged, what to do straight away, and how to get the footage back.

Why these cameras produce broken videos

Almost all of them record MP4 or MOV files using H.264 or H.265 (HEVC) video. While filming, they stream picture and sound onto the card; when the clip ends, they write an index that tells players where everything is. If that last step doesn't happen, the file is full of footage but unplayable.

DeviceCommon cause of damageTypical symptom
DroneBattery ran out, crash, or the drone shut down on landing while still recordingLast clip of the flight won't play or shows 0:00
DashcamIgnition switched off or a crash cut power mid-clip; worn card from constant loop recordingThe clip you need, often the incident itself, is the broken one
Action cameraBattery died, camera knocked or the card jolted loose, overheatingFinal chapter of a long recording won't open

Many action cameras also split long recordings into several files, called chapters. Usually only the last chapter is damaged; the earlier ones play normally.

Dashcams work in a similar way, recording a continuous series of short clips, typically one to a few minutes long. When power is cut, the clip being written at that moment is the one at risk, and with an accident that is very often the clip that matters most. Earlier clips in the sequence are normally fine, so check them too for the lead-up to the event.

What to do first

  1. Stop recording on that card. This matters most for dashcams. Loop recording overwrites the oldest clips automatically, so remove the card or switch the dashcam off as soon as you know you need a clip. Many dashcams also have a locked or event folder where impact-triggered clips are protected; check it.
  2. Don't format the card, even if the camera or an app prompts you to.
  3. Give the device a chance. Some cameras check for an unfinished recording when they power on with a charged battery and the same card, and try to close it. If yours offers, let it.
  4. Copy the entire card to your PC with a card reader, keeping the folder structure. Work on the copies only.
  5. Try the clip in VLC. Install HEVC Video Extensions from the Microsoft Store too, as many of these devices record in H.265. If the clip plays once the codec is installed, it was never damaged.

How to repair the video with File Repairer

File Repairer is Windows software that repairs MP4, MOV, AVI and MKV videos that won't play, freeze or have no sound. Its sample-file repair is built for recordings cut off by a dead battery or a full card on phones, cameras, GoPro-style action cams, drones and dashcams, and handles both H.264 and H.265/HEVC. Footage stays on your PC; nothing is uploaded, which also matters when a dashcam clip may be needed for an insurance claim.

  1. Drag the copied folder from the card into File Repairer. To see which clips are actually broken, use Tools > Check Files for Damage; it marks each file Damaged or No damage found without changing anything.
  2. Click Repair All. Lightly damaged clips may be repaired straight away.
  3. For any clip marked Needs a sample file, add a working video from the same device.
  4. Preview video frames and check the "what was recovered" panel.
  5. Save the repaired copies. Each gets " (repaired)" in its name; the original files are never changed or overwritten.

Checking, repairing and previewing are free. Saving the repaired copies needs an Installation Key.

Choosing a good sample clip

  • Same device. A clip from a different drone or dashcam model won't match how the footage was written.
  • Same settings. Match resolution, frame rate and codec. If the broken clip was 4K at 60 fps in H.265, the sample should be too.
  • Same modes. If you used HDR, a log color profile or a stabilization mode, use a sample recorded the same way.
  • Any length. A few seconds is enough. Another clip from the same flight, drive or session is ideal. If you have none, record a short one now with identical settings.

Our guide on fixing a video after the battery died goes into more detail on sample-file repair.

What you can and can't get back

  • Footage that reached the card can usually be rebuilt, with picture and sound where the device recorded sound.
  • The final moments before power was lost may never have been written, so the repaired clip can end a little early.
  • Overwritten dashcam clips are gone. Loop recording replaces old footage with new, and no repair can reverse that.
  • Drone audio usually isn't there to begin with, since most drones don't record sound. A silent drone clip is normal; see video has no sound for other cases.
  • Missing files that no longer appear on the card need data recovery software first. File Repairer repairs files you have; it doesn't undelete or read cards your PC can't see. Then see recovered files that won't open.

How to reduce the risk next time

  • Use high-endurance cards in dashcams, which write constantly, and replace them periodically.
  • Format the card in the device after backing it up, not on the PC.
  • Stop recording before landing or before the battery reaches its low-power cutoff.
  • Check dashcam power settings so the camera has time to close the clip when the ignition goes off.
  • Back up after every trip, so one damaged card never holds your only copy.

Frequently asked questions

How do I stop my dashcam overwriting the clip I need?

Remove the card or switch the dashcam off as soon as you can, because loop recording replaces the oldest footage first. Check the locked or event folder too, where impact-triggered clips are often protected.

Only the last chapter of my action cam recording is broken. Is that normal?

Yes. When long recordings are split into chapters, the earlier ones are already closed properly, so only the chapter being recorded when power was lost is usually damaged.

Can I repair a drone video if the drone was lost?

Only if you have the video file. If footage was saved to the drone's card and the drone wasn't recovered, there's nothing to repair, though some apps keep a lower-quality cached copy on your phone or controller.

Get three guides like this every month, plus software update notices.Subscribe →